
KENR8601 93
Troubleshooting Section
Expected Result:
There is a letter “E” after the number of the CID that
is on the upper display panel of the EMCP II+P.
Results:
•
YES – There is a letter “E” after the number of the
CID that is on the upper display panel of the EMCP
II+P .
Repair: Troubleshoot the diagnostic code for
the Engine ECM. Refer to Troubleshooting,
RENR9348 or System Operation Testing
and Adjusting, RENR9968 for information on
troubleshooting the diagnostic code.
STOP.
•
NO – There is not a letter “E” after the number of
the CID that is on the upper display panel of the
EMCP II+P .
Repair: There may be a problem with the CAT
Data Link. Determine if CID 0248 FMI 09 is
present. Refer to Diagnostic Code Procedures,
“GSC CID 0248 - FMI 09”.
STOP.
i02897409
GSC CID 0110 - FMI 02
SMCS Code: 1906-035
Conditions Which Generate This Code:
The engine ECM monitors engine coolant
temperature in order to protect the engine from a
problem with the coolant temperature. The coolant
temperature sensor is mounted in the water jacket,
close to the front of the engine. The exact location
of the engine coolant temperature sensor varies
depending on the engine model.
The GSC+P monitors the coolant temperature that is
read by the engine ECM. The engine ECM sends the
information to the GSC+P by the CAT data link.
The possible causes of a CID 0110 FMI 02 are listed
below:
•
There is an open circuit on the CAT data link
between the engine ECM and the GSC+P.
•
There is a problem with the temperature sensor
that is connected to the engine ECM.
If a CID 0248 FMI 09 for the CAT data link is active,
correct the diagnostic code prior to proceeding with
this procedure.
System Response:
Note: The GSC+P is usually programmed to treat
a problem with the coolant temperatu re s ensor as
an alarm fault. Setpoint P004 is 0. If the GSC+P is
programmed to treat a problem with the oil pressure
sensor as a s hutdown fault, setpoint P04 is 1. If
setpoint P04 is programmed to 1, the diagnostic code
is automatically shown in the upper display.
Note: Diagnostic codes are created when the
harness connector is disconnected from the GSC+P
during the troubleshooting procedures. Clear these
created diagnostic codes after the particular problem
is corrected. In a properly operating system, when
the harness connector is removed from the GSC+P,
the following diagnostic codes are recorded.
Test Step 1. VERIFY THE DIAGNOSTIC
CODE.
View the diagnostic code that is displayed on the
upper display panel of the EMCP II+P. Determine if
the diagnostic code is originatin g from the Eng ine
ECM.
Expected Result:
There is a letter “E” after the number of the CID that
is on the upper display panel of the EMCP II+P.
Results:
•
YES – There is a letter “E” after the number of
the CID that is on the upper display panel of the
EMCP II+P.
Repair: Troubleshoot the diagnostic code for
the Engine E CM. Refer to Troubleshooting,
RENR9348 or System Operation Testing and
Adjusting, RENR9968.
STOP.
•
NO – There is not a letter “E” after the number of
the CID that is on the upper display panel of the
EMCP II+P. Proceed to Test Step 2.
Tes t Step 2. CHECK FOR AN OPEN
CIRCUIT ON THE CAT DATA LINK.
A. Turn the ECS to the OFF/RESET position.
B. Disconnect the harness connector from the
GSC+P. Disconnect the harness connector from
theengineECM.
C. At the harness connector for the engine ECM,
connect a jumper wire between pin J1-9 and pin
J1-3.
D. At the h arness connector for the GSC+P, measure
the resistance between pin 19 and pin 20.