
KENR8601 123
Troubleshooting Section
Results:
•
OK – The resistance measurements are correct.
Proceed to Test Step 3.
•
NOT OK – The resistance measurements are
NOT c orrect. The harness wiring with the incorrect
resistance measurement is open or the harness
wiring has failed.
Repair: Repair the harness wiring or replace
the harness wiring. Repair the wiring or replace
thewiringbetweenthe“BATT-”,theECS,and
the GSC+P connector. Reconnect the remote
start/stop initiate contacts after the troubleshooting
is completed.
STOP.
Te st Step 3. CHECK FOR AN OPEN
CIRCUIT IN THE “MAN/START”
POSITION
A. If equipped, the remote start/stop initiate contacts
will remain disconnected from the terminal strip in
the customers’ connection box.
B. The harness connector remains disconnected
from the GSC+P.
C. Check whether the corresponding contact of the
GSC+P harness connector is the only contact that
is connected to the battery negative.
D. Place the ECS in the MAN/START position.
Measure the resistance from pin “33” of the
GSC+P harness connector to the “BATT-” terminal
of the relay module. Measure the resistance from
pins “32”, “39” and “40” to the “BATT-” terminal.
Make a note of the resistances that are measured.
Expected Result:
The resistance that is measured from pin “33” to the
“B−” terminal of the relay module should be 5 ohms
or less. The resistance that is measured from pins
“32”, “39” and “40” to the “B−” terminal should be
greater than 5000 ohms.
Results:
•
OK – The resistance measurements are correct.
Proceed to Test Step 4.
•
NOT OK – The resistance measurements are
NOT c orrect. The harness wiring with the incorrect
resistance measurement is open or the harness
wiring has failed.
Repair: Repair t he harnes s wiring or replace
the harness wiring. Rep air the wiring or replace
the wiring between the “BATT-”, the ECS, and
the GSC+P connector. Reconnect the remote
start/stop initiate contacts after the troubleshooting
is comp leted.
STOP.
Tes t Step 4. CHECK FOR AN OPEN
CIRCUIT IN THE “COOLDOWN/STOP”
POSITION
A. If equipped, the remote s tart/stop initiate contacts
will rema in disconnected from the term inal strip in
the customers’ connection box.
B. The harness connector remains disconnected
from the G SC+P.
C. Check whether the corresponding contact of the
GSC+P harness connector is the only c ontact that
is connected to the “BATT-”.
D. Place the ECS in the COOLDOWN/STOP position.
Measure the resistance from pin “32” of the
GSC+P harness connector to the “BATT-” terminal
of the relay module. Measure the resistance from
pins “33”, “39” and “40” to the “BATT-” terminal.
Make a note of the resistances that are measured.
Expected Result:
The resistance that is measured from pin “32” to
the “BATT-” terminal of the relay module should be
5 ohms or less. The resistance that is measured
from pins “33”, “39” and “40” to the “BATT-” terminal
should be greater than 5000 ohms.
Results:
•
OK – The resistance measurements are correct.
STOP.
•
NOT OK – The resistance measurements are
NOT correct. T he harness wiring with the inco rrect
resistance measurement is open or the harness
wiring has failed.
Repair: Repair t he harnes s wiring or replace
the harness wiring. Rep air the wiring or replace
the wiring between the “BATT-”, the ECS, and
the GSC+P connector. Reconnect the remote
start/stop initiate contacts after the troubleshooting
is comp leted.
STOP.