
RENR9716-02 91
Disassembly and Assembly Section
Note: Bolt (B) is on the opposite side of the bearing
tab of the main b
earing cap.
c. Tighten Bolt (B) for an additional 120 ± 5
degrees (2 flat
s).
Note: If Tooling (E) is not used, place an index mark
on the bolt and
the main bearing cap.
d. Tighten Bolt (A) for an additional 120 ± 5
degrees (2 flat
s).
Note: If Tooling (E) is not used, place an index mark
on the bolt an
d the main bearing cap.
e. TightenBolt(D)toatorqueof80±10N·m
(59±7lbft).
Note: Bolt (D) is on the opposite side of the bearing
tab of the mai
n bearing cap.
f. TightenBolt(C)toatorqueof80±10N·m
(59±7lbft).
Note: Bolt (C) is on the bearing tab side of the main
bearing cap
.
g. Rotate the crankshaft in order to ensure that
the cranksh
aft turns freely.
12. Use Tooling (D) to check the crankshaft end play.
Ensure that
Tooling (D) is against a machined
surface. The end play is controlled by the thrust
plates of No. 4 main bearing (center).
Crankshaft end play (new thrust
plates) ...... 0.10 to 0.60 mm (0.004 to 0.024 inch)
Note: Install the connecting rod bearings dry
when clearance checks are performed. Refer to
Disassemb
ly and Assembly, “Bearing Clearance -
Check”. Apply clean engine oil on the connecting rod
bearings for final assembly.
g01150364
Illustration 262
13. Position the connecting rod against the
crankshaft. Install connecting rod bearing cap (2)
on the connecting rod.
Note: Ensure that the number on the side of the
connecting rod
bearingcapisonthesamesideas
the number on the connecting rod. The bearing tabs
of the connecting rod bearing cap and the connecting
rod a re locate
d on the side opposite of the piston
cooling jet.
14. Lubricate th
e threads of bolts (1) with clean
engine oil. Install the bolts.
15. Tighten bolt
s(1),asfollows:
a. Tighten Bolt (A) and Bolt (C) to a torque of
70 ± 4 N·m (52 ±
3lbft).
b. Tighten Bolt (B) and Bolt (D) to a torque of
70 ± 4 N·m (52 ±
3lbft).
c. Turn Bolt (B) and Bolt (D) for an additional 60 ±
5 degrees (1/
6 turn).
Note: If Tooling (E) is not used, place an index mark
on each bolt
and connecting rod cap.
d. Tighten Bolt (A) and Bolt (C) again to a torque
of 70 ± 4 N·m (
52 ± 3 lb ft).
e. Turn Bolt (A) and Bolt (C) for an additional 60 ±
5 degrees (1
/6 turn).
Note: If Tooling (E) is not used, place an index mark
on each bolt
and connecting rod cap.
f. Rotate the crankshaft in order to ensure that
the cranksh
aft turns freely.
End By:
a. Install the piston cooling jets. Refer to Disassembly
and Assembly, “Piston Cooling Jets - Remove
and Instal
l”.
b. Install the rear housing. Refer to Disassembly and
Assembly,
“Housing (Rear) - Install”.
c. Install the front housing. Refer to Disassembly and
Assembly,
“Housing (Front) - Install”.