
90 SEBU8088-06
Maintenance Section
Cooling System Coolant Sample (Level 2) - Obtain
Obtain the samp
le of the coolant as close as possible
to the recommended sampling interval. In order
to receive the full effect of S·O·S analysis, you
must establis
h a consistent trend of data. In order
to establish a pertinent history of data, perform
consistent samplings that are evenly spaced.
Supplies for
collecting samples can be obtained from
your Caterpillar dealer.
Use the follo
wing guidelines for proper sampling of
the coolant:
•
Complete the
information on the label for the
sampling bottle before you begin to take the
samples.
•
Keep the unused sampling bottles stored in plastic
bags.
•
Obtain coolant samples directly from the coolant
sample port. You should not obtain the samples
from any ot
her location.
•
Keep the lids on empty sampling bottles until you
are ready t
o collect the sample.
•
Place the sample in the mailing tube immediately
after obta
ining the sample in order to avoid
contamination.
•
Never coll
ect samples from expansion bottles.
•
Never collect samples from the drain for a system.
Submit the sample for Level 1 analysis.
For additi
onal information about coolant analysis,
see this Operation and Maintenance Manual, “Refill
Capacities and Recommendations” or consult your
Caterpil
lar dealer.
i0198771
4
Coo ling System Coo lant
Sample (L
evel 2) - Obtain
SMCS Code: 1350-008; 1395-008; 1395-554; 7542
NOTICE
Always use a designated pump for oil sampling, and
use a separate designated pump for coolant sampling.
Using the same pump for both types of samples may
contaminate the samples that are being drawn. This
contaminate may cause a false analysis and an incor-
rect interpretation that could lead to concerns by both
dealers and customers.
Refer to Operation and Maintenance Manual,
“Cooling System Coolant Sample (Level 1) - Obtain”
for the guidelines for proper sampling of the coolant.
Submit the samp
le for Level 2 analysis.
For additional information about coolant
analysis, see
Special Publication, SEBU6251,
“Caterpillar Commercial Diesel Engines Fluids
Recommendations” or consult your Caterpillar dealer.
i02839449
Cooling System Supplemental
Coolant Additive (SC A) -
Test/Add
SMCS Code: 1352-045; 1395-081
Cooling sys
tem coolant additive contains alkali.
To he lp prevent personal injury, avoid contact with
the skin and eyes. Do not drink cooling system
coolant ad
ditive.
NOTICE
Excessive supplemental coolant additive concentra-
tion can form deposits on the higher temperature sur-
faces of the cooling system, reducing the engine’s
heat transfer characteristics. Reduced heat transfer
could cause cracking of the cylinder head and other
high temperature components.
Excessive supplemental coolant additive concentra-
tion could also result in blockage of the heat exchang-
er, overheating, and/or accelerated wear of the water
pump seal.
Do not exceed the recommended amount of supple-
mental coolant additive concentration.
NOTICE
Care must be taken to ensure that fluids are contained
during performance of inspection, maintenance, test-
ing, adjus
ting and repair of the product. Be prepared to
collect the fluid with suitable containers before open-
ing any compartment or disassembling any compo-
nent cont
aining fluids.
Refer to Special Publication, NENG2500, “Caterpillar
Dealer Se
rvice Tool Catalog” and to Special Publica-
tion, GECJ0003, “Cat Shop Supplies and Tools” for
tools and supplies suitable to collect and contain flu-
ids on Ca
terpillar products.
Dispose of al l fluids according to applicable regula-
tions an
d mandates.
Note: Caterpillar recommends an S·O·S coolant
analysis (Level 1).