
42 SEBU8088-06
Operation Section
Features and Controls
•
fault shutdown
indicator (25)
•
spare fault indicators (28)
•
dedicated shutdown indicators (27)
The yellow fau
lt alarm indicator (26) FLASHES when
the GSC+ detects an alarm fault. The alarm fault
does not cause the engine status to change. The
engine can be s
tarted. The engine will continue
operating only if the engine is running at the time
of the alarm fault. Fault alarm indicator (26) is
accompanied
by an alarm fault code that is shown
on the upper display (29) when the alarm codes
key (30) is pressed. For the descriptions of the fault
codes, refer
to the Systems Operation, Testing and
Adjusting, RENR2484, “Electronic Modular Control
Panel II + (EMCP II+)”.
The red fault shutdown indicator (25) FLASHES
when the GSC+ detects a shutdown fault. The engine
will shut d
own if the engine is running. The engine will
not be allowed to start. Fault shutdown indicator (25)
is accompanied by a fault code that is immediately
shownonth
e upper display (29). For the descriptions
of the fault codes, refer to the Systems Operation,
Testing and Adjusting, RENR2484, “Electronic
Modular C
ontrol Panel II + (EMCP II+)”.
The yellow spare fault indicators (28) can be used for
parallel
ing as a redundant sync check. During the
paralleling process and before the circuit breaker
is closed, the lamps will indicate if the generator is
in sync wi
th the bus. The spare fault indicators are
listed below.
•
generat
or voltage match (spare 1 indicator)
•
generator frequency match (spare 2 indicator)
•
generator phasing match (spare 3 indicator)
If the ge
nerator parameters are not matched to
the bus, the associated lamp will flash. When the
generator and bus voltages, frequencies and phases
areinsy
nc, the lamps will light continuously.
When the contro
l panel is not in a paralleling mode,
the same three spare fault indicators (28) can be
programmed by the customer. The three spare
faults can be p
rogrammed to show coolant loss, oil
temperature, spare fault condition or no assignment.
The yellow spare fault indicators (28) FLASH when
the conditio
ns that are associated with that spare
fault are active. The yellow fault alarm indicator
(26) or the red fault shutdown indicator (25) will
accompany t
he spare fault indicators (28). The
spare fault indicators will tell whether the spare fault
input is programmed to be an alarm condition or a
shutdown co
ndition. For the descriptions of the fault
codes, refer to the Systems Operation, Testing and
Adjusting, RENR2484, “Electronic Modular Control
Panel II + (
EMCP II+)”.
The red dedicated shutdown indicators (27) represent
the follow
ing shutdown faults: low oil pressure,
emergency stop, high water temperature, engine
overspeed and engine overcrank. When the GSC+
detects a
fault in one of these areas, the dedicated
shutdown indicator (that corresponds to the fault)
FLASHES. The engine is shutdown if the engine
is runnin
g, and the engine is not allowed to start.
No fault codes are associated with the dedicated
shutdown indicators because each indicator has a
descrip
tive label.
Many of the dedicated shutdown faults depend on
certain
setpoints in the GSC+. For the descriptions
of the fault codes, refer to the Systems Operation,
Testing and Adjusting, RENR2484, “Electronic
Modular
Control Panel II + (EMCP II+)”.
The conditions that are required to activate the
dedica
ted fault shutdowns and the results of each
dedicated fault are in the following list.
______
___________________________________________________________
Low Oil Pressure – The engine oil pressure drops
below t
he setpoints for low oil pressure shutdown
that are programmed into the GSC+. There are two
low oil pressure setpoints. One setpoint is used when
the eng
ine is at idle speed. The other setpoint is used
when the engine is at rated speed. When a low oil
pressure fault occurs, the low oil pressure indicator
FLASH
ES, and the engine is shut down. The engine
is not allowed to start until the fault is corrected.
Emerg
ency Stop – The operator presses the
Emergency Stop Push Button (ESPB) on the front
panel. When an emergency stop condition occurs,
the e
mergency stop indicator FLASHES and the
engine is shut down. The engine is not allowed to
start until the condition is corrected.